Tombstoning Root Cause Analysis

A tombstoned component stands on one end, lifted off the second pad with its unmetallised side in the air. It is one of the most recognisable defects in surface mount assembly and also one of the most misdiagnosed, because the visible result is produced by several different mechanisms. Reflow imbalance, pad geometry, paste volume differences and placement offset can all lift a chip, and each has a different fix. This article sets out how to tell them apart.

What Tombstoning Looks Like

The part rotates about one termination as the alloy on that pad melts first and wets the metallisation, pulling the component upright. The second end is left standing clear of its pad or held only by a thin bridge. The phenomenon is most common on small chip components, especially the smallest body sizes, because their mass is low and the surface tension of a small fillet is more than enough to move them.

It is not restricted to the smallest parts. Larger chips tombstone when one pad heats very differently from the other, and the defect also appears on chip resistors and on small diodes and capacitors where one termination connects to a large thermal mass. The size of the part sets how much imbalance is needed, not whether imbalance matters.

The Thermal Imbalance Mechanism

The sequence is straightforward once seen. One pad reaches liquidus and wets its termination before the other, and the resulting surface tension pulls the component towards that side. By the time the second pad melts, the body has already rotated, and gravity cannot return a body that light to its proper position. The window in which this can happen is short, which is why the defect appears sporadically.

Thermal imbalance is created by the layout as much as by the oven. A pad connected to a ground plane through a wide thermal spoke heats more slowly than an isolated pad, so the two terminations of one component reach temperature at different times. Removing or narrowing the spoke, or making the connection symmetrical, removes the mechanism.

Pad Geometry and Solder Volume

Paste volume is proportional to aperture area, so a pad design that makes one aperture larger than the other guarantees that one end of the part receives more alloy. That difference alone is often enough to rotate a small chip, because the larger deposit produces a stronger pull as it melts. The fix is to keep the two apertures identical in area even when the pads must differ for thermal reasons.

Pad width and length also set the moment arm. An oversized pad allows the component to slide and gives the molten fillet more leverage, while a pad that is too short gives a weak fillet and poor self alignment. Recommended land patterns exist for a reason, and departing from them for the sake of a tighter layout usually costs more in defects than it saves in area.

Additional Considerations for This Build

Practical attention to component lift pays for itself here, because it decides whether the finished board behaves as the drawing intended. Where the requirement is not stated on the fabrication drawing or in the assembly notes, the shop has to assume a default, and that default is rarely the value the design was simulated with. Stating component lift explicitly, together with the tolerance that applies, removes the assumption and keeps the result predictable from batch to batch.

Process Control and Verification

On a design of this kind, placement offset is the item that decides how the rest of the board is arranged. Documenting the assumption is part of the design work, and a short note on the drawing prevents a question that would otherwise arrive a day later and cost a day of schedule. The process window is set by the narrowest step in the flow, so an improvement anywhere else shows up as margin rather than as yield until that step is addressed.

A short note on the drawing about handling, storage or packaging is often worth more than an extra decimal place on a tolerance. Where a value sits close to a process limit, the drawing should say so, since the shop can then open the process window rather than working to a nominal figure that carries no tolerance.

A stack-up that is drawn rather than described removes most of the ambiguity from a quotation, and it lets the fabricator price the board against the dielectric and copper weights that will actually be used. Where the requirement is not written down, the shop supplies its own default, and the default is chosen for the process rather than for the design.

The measurements that matter are the repeatable ones: conductor width and spacing, annular ring, finished hole size, plating thickness and surface finish are all verifiable on a coupon that travels with the panel. Running a first article through the same checks as the production panel confirms that the two agree, and that comparison is the cheapest form of process control available at prototype stage.

Keeping a sample from the panel turns a dispute into a measurement, because the same coupon can be re-examined by both parties without rebuilding the batch.

Related reading: our fabrication notes, board quality and design release notes cover the same ground.

Process Control and Verification

On a design of this kind, placement offset is the item that decides how the rest of the board is arranged. Documenting the assumption is part of the design work, and a short note on the drawing prevents a question that would otherwise arrive a day later and cost a day of schedule. The process window is set by the narrowest step in the flow, so an improvement anywhere else shows up as margin rather than as yield until that step is addressed.

A short note on the drawing about handling, storage or packaging is often worth more than an extra decimal place on a tolerance. Where a value sits close to a process limit, the drawing should say so, since the shop can then open the process window rather than working to a nominal figure that carries no tolerance.

Process Control and Verification

On a design of this kind, placement offset is the item that decides how the rest of the board is arranged. Documenting the assumption is part of the design work, and a short note on the drawing prevents a question that would otherwise arrive a day later and cost a day of schedule. The process window is set by the narrowest step in the flow, so an improvement anywhere else shows up as margin rather than as yield until that step is addressed.

A first article check confirms that the process and the drawing agree on the points listed above, and that the coupon data supports the values used in the design.

Where a measurement falls outside the expected window, the sample is retained so that the cause can be established before the balance of the batch is released.

Paste Deposition Differences

Two apertures of identical area can still receive different volumes. A stencil that is worn on one side, a squeegee that is not parallel to the board, or a clogged aperture all change the deposit on one pad only. Because the defects then follow the stencil rather than the layout, comparing the position of the tombstoned parts across a panel is a useful diagnostic step.

Solder paste inspection makes this visible. When deposit volumes for a pair of pads differ by more than about twenty per cent, the risk rises sharply on small components. Reviewing the volume distribution by aperture position identifies whether the problem is the stencil, the printer setup or the paste itself.